{"title":"Komatsu Hydraulic Seal Kits","description":"\u003cp\u003eAftermarket hydraulic cylinder seal kits for Komatsu equipment, listed by OEM kit number. Each listing gives the machine models, rod and bore sizes and the kit contents.\u003c\/p\u003e","products":[{"product_id":"07002-12034-hydraulic-cylinder-seal-kit-fits-komatsu-replaces-07002-02034","title":"07002-12034 Hydraulic Cylinder Seal Kit Fits Komatsu Replaces 07002-02034 - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 07002-12034 on Komatsu Replaces 07002-02034. \u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e07002-12034\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu Replaces 07002-02034\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 07002-12034 on Komatsu Replaces 07002-02034. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 07002-12034.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"50-Pack","offer_id":48855039443149,"sku":"SK.07002-12034-KOM.50.BI.OEM.B70","price":28.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_f8f63ce2-a807-4385-b194-2bbc6a4b980c.jpg?v=1794370826"},{"product_id":"07002-13034-hydraulic-cylinder-seal-kit-fits-komatsu","title":"07002-13034 Hydraulic Cylinder Seal Kit Fits Komatsu - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 07002-13034. \u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e07002-13034\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 07002-13034. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 07002-13034.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"10-Pack","offer_id":48855039475917,"sku":"SK.07002-13034-KOM.10.BI.OEM.B90","price":27.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_33277f88-0068-4414-b0ba-f0236e08bd8a.jpg?v=1794370827"},{"product_id":"07145-00080-hydraulic-cylinder-seal-kit-fits-komatsu","title":"07145-00080 Hydraulic Cylinder Seal Kit Fits Komatsu - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 07145-00080. \u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e07145-00080\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 07145-00080. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 07145-00080.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855039541453,"sku":"SK.07145-00080-KOM.BI.OEM.B90","price":31.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_47a312a0-a7e6-48e8-ab33-5d2a6a4aba2a.jpg?v=1794370829"},{"product_id":"101-63-02010k-lift-cylinder-seal-kit-fits-komatsu-d20a-7-d21a-7-35mm-rod-x-70mm-bore","title":"101-63-02010K Lift Cylinder Seal Kit Fits Komatsu D20A-7 D21A-7, 35mm rod x 70mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 101-63-02010K, for the lift cylinder on Komatsu D20A-7 D21A-7. It is sized for a 35mm rod x 70mm bore cylinder. Kit contents: Wiper, U cup, wear band, T Seal, 2pc oring and backup seals.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e101-63-02010K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D20A-7 D21A-7\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eLift Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e35mm rod x 70mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, wear band, T Seal, 2pc oring and backup seals\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 101-63-02010K on Komatsu D20A-7 D21A-7. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 101-63-02010K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855039901901,"sku":"SK.101-63-02010K-KOM.BI.OEM","price":59.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_c992fb79-ae94-4df1-962f-4fcf01ce81cb.jpg?v=1794370844"},{"product_id":"101-63-02030k-hydraulic-cylinder-seal-kit-fits-komatsu-d20a-7-d21a-7-35mm-rod-x-70mm-bore","title":"101-63-02030K Hydraulic Cylinder Seal Kit Fits Komatsu D20A-7 D21A-7, 35mm rod x 70mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 101-63-02030K on Komatsu D20A-7 D21A-7. It is sized for a 35mm rod x 70mm bore cylinder. Kit contents: Wiper, U cup, wear band, T Seal, 2pc oring and backup seals.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e101-63-02030K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D20A-7 D21A-7\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e35mm rod x 70mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, wear band, T Seal, 2pc oring and backup seals\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 101-63-02030K on Komatsu D20A-7 D21A-7. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 101-63-02030K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855039934669,"sku":"SK.101-63-02030K-KOM.BI.OEM","price":59.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_0e989e08-1fab-456f-b07c-af23a19dd5f0.jpg?v=1794370846"},{"product_id":"101-63-02040k-tilt-cylinder-seal-kit-fits-komatsu-d20a-7-d21a-7-40mm-rod-x-80mm-bore","title":"101-63-02040K Tilt Cylinder Seal Kit Fits Komatsu D20A-7 D21A-7, 40mm rod x 80mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 101-63-02040K, for the tilt cylinder on Komatsu D20A-7 D21A-7. It is sized for a 40mm rod x 80mm bore cylinder. Kit contents: Wiper, U cup, wear band, Buffer , 2pc oring and backup seals.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e101-63-02040K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D20A-7 D21A-7\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eTilt Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e40mm rod x 80mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, wear band, Buffer , 2pc oring and backup seals\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 101-63-02040K on Komatsu D20A-7 D21A-7. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 101-63-02040K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855039967437,"sku":"SK.101-63-02040K-KOM.BI.OEM","price":62.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_0a1f2645-75a8-45cd-831b-0e3bc4c05cbc.jpg?v=1794370849"},{"product_id":"101-63-02130k-hydraulic-cylinder-seal-kit-fits-komatsu-d20a-7-d21a-7-35mm-rod-x-70mm-bore","title":"101-63-02130K Hydraulic Cylinder Seal Kit Fits Komatsu D20A-7 D21A-7, 35mm rod x 70mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 101-63-02130K on Komatsu D20A-7 D21A-7. It is sized for a 35mm rod x 70mm bore cylinder. Kit contents: Wiper, U cup, wear band, 4pc rod seal, T Seal, 2pc oring and backup seals.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e101-63-02130K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D20A-7 D21A-7\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e35mm rod x 70mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, wear band, 4pc rod seal, T Seal, 2pc oring and backup seals\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 101-63-02130K on Komatsu D20A-7 D21A-7. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 101-63-02130K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855040000205,"sku":"SK.101-63-02130K-KOM.BI.OEM","price":71.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_a98e645d-df16-4566-a0c0-f84afabd0039.jpg?v=1794370849"},{"product_id":"101-63-02140k-hydraulic-cylinder-seal-kit-fits-komatsu-d20a-7-d21a-7-35mm-rod-x-70mm-bore","title":"101-63-02140K Hydraulic Cylinder Seal Kit Fits Komatsu D20A-7 D21A-7, 35mm rod x 70mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 101-63-02140K on Komatsu D20A-7 D21A-7. It is sized for a 35mm rod x 70mm bore cylinder. Kit contents: Wiper, U cup, wear band, 4pc rod seal, T Seal, 2pc oring and backup seals.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e101-63-02140K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D20A-7 D21A-7\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e35mm rod x 70mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, wear band, 4pc rod seal, T Seal, 2pc oring and backup seals\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 101-63-02140K on Komatsu D20A-7 D21A-7. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 101-63-02140K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855040032973,"sku":"SK.101-63-02140K-KOM.BI.OEM","price":70.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_a4af10a3-0fb9-45d7-96d3-38c1f26fd677.jpg?v=1794370849"},{"product_id":"114-63-05030-hydraulic-cylinder-seal-kit-fits-komatsu-d31a-17-d31p-17-d37e-1-40mm-rod-x-90","title":"114-63-05030 Hydraulic Cylinder Seal Kit Fits Komatsu D31A-17 D31P-17 D37E-1, 40mm rod x 90mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 114-63-05030 on Komatsu D31A-17 D31P-17 D37E-1. It is sized for a 40mm rod x 90mm bore cylinder. Kit contents: Wiper, U cup, 3pc oring, T Seal, wear band and backup seals.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e114-63-05030\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D31A-17 D31P-17 D37E-1\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e40mm rod x 90mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, 3pc oring, T Seal, wear band and backup seals\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 114-63-05030 on Komatsu D31A-17 D31P-17 D37E-1. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 114-63-05030.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855040262349,"sku":"SK.114-63-05030-KOM.BI.OEM","price":58.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_707a3edc-a66a-4451-aa32-b48dcd76164b.jpg?v=1794370860"},{"product_id":"12f-63-05020-lift-cylinder-seal-kit-fits-komatsu-d40a-3-d41a-3-45mm-rod-x-70mm-bore","title":"12F-63-05020 Lift Cylinder Seal Kit Fits Komatsu D40A-3 D41A-3+, 45mm rod x 70mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 12F-63-05020, for the lift cylinder on Komatsu D40A-3 D41A-3+. It is sized for a 45mm rod x 70mm bore cylinder. Kit contents: Wiper, U cup, T seal, 5pc oring, wear band and backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e12F-63-05020\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D40A-3 D41A-3+\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eLift Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e45mm rod x 70mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, T seal, 5pc oring, wear band and backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 12F-63-05020 on Komatsu D40A-3 D41A-3+. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 12F-63-05020.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"3-Pack","offer_id":48855047110861,"sku":"SK.12F-63-05020-KOM.3.BI.OEM","price":190.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_6991986c-505b-46b6-9354-8f83fe8b558b.jpg?v=1794371132"},{"product_id":"12f-63-05060-tilt-cylinder-seal-kit-fits-komatsu-d41e-3-50mm-rod-x-100mm-bore","title":"12F-63-05060 Tilt Cylinder Seal Kit Fits Komatsu D41E-3, 50mm rod x 100mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 12F-63-05060, for the tilt cylinder on Komatsu D41E-3. It is sized for a 50mm rod x 100mm bore cylinder. Kit contents: Wiper, U cup, 2pc rod seal, T seal, 5pc oring, wear band and backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e12F-63-05060\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D41E-3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eTilt Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e50mm rod x 100mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, 2pc rod seal, T seal, 5pc oring, wear band and backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 12F-63-05060 on Komatsu D41E-3. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 12F-63-05060.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"3-Pack","offer_id":48855047143629,"sku":"SK.12F-63-05060-KOM.3.BI.OEM","price":351.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_662ec7a2-b738-4642-a293-9aa0bb1a9e33.jpg?v=1794371134"},{"product_id":"130-63-05020-lift-cylinder-seal-kit-fits-komatsu-d50p-16-d53p-16-55mm-rod-x-90mm-bore","title":"130-63-05020 Lift Cylinder Seal Kit Fits Komatsu D50P-16 D53P-16, 55mm rod x 90mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 130-63-05020, for the lift cylinder on Komatsu D50P-16 D53P-16. It is sized for a 55mm rod x 90mm bore cylinder. Kit contents: Wiper, U cup, 2pc load U cup, 2pc rod seal, 6pc oring, wear band and backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e130-63-05020\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D50P-16 D53P-16\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eLift Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e55mm rod x 90mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, 2pc load U cup, 2pc rod seal, 6pc oring, wear band and backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 130-63-05020 on Komatsu D50P-16 D53P-16. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 130-63-05020.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"3-Pack","offer_id":48855047176397,"sku":"SK.130-63-05020-KOM.3.BI.OEM","price":345.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_e0ceb3e4-3edd-4803-a646-e577b554ee21.jpg?v=1794371137"},{"product_id":"130-63-12173-hydraulic-cylinder-seal-kit-fits-komatsu","title":"130-63-12173 Hydraulic Cylinder Seal Kit Fits Komatsu - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 130-63-12173. \u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e130-63-12173\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 130-63-12173. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 130-63-12173.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"10-Pack","offer_id":48855047209165,"sku":"SK.130-63-12173-KOM.10.BI.OEM.PU","price":95.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_4f223723-359c-4eb4-93b0-f5c6b39119fd.jpg?v=1794371137"},{"product_id":"131-63-05020-hydraulic-cylinder-seal-kit-fits-komatsu-d50s-16-d53s-16-65mm-rod-x-130mm-bor","title":"131-63-05020 Hydraulic Cylinder Seal Kit Fits Komatsu D50S-16 D53S-16, 65mm rod x 130mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 131-63-05020 on Komatsu D50S-16 D53S-16. It is sized for a 65mm rod x 130mm bore cylinder. Kit contents: Wiper, 3pc U cup, 4pc oring, 4pc rod seal, wear band and backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e131-63-05020\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D50S-16 D53S-16\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e65mm rod x 130mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, 3pc U cup, 4pc oring, 4pc rod seal, wear band and backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 131-63-05020 on Komatsu D50S-16 D53S-16. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 131-63-05020.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"3-Pack","offer_id":48855047241933,"sku":"SK.131-63-05020-KOM.3.BI.OEM","price":383.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_9a2df956-5fef-4ce6-a59c-d332134445a8.jpg?v=1794371137"},{"product_id":"135-63-05020-hydraulic-cylinder-seal-kit-fits-komatsu-d57s-1b-65mm-rod-x-140mm-bore","title":"135-63-05020 Hydraulic Cylinder Seal Kit Fits Komatsu D57S-1B, 65mm rod x 140mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 135-63-05020 on Komatsu D57S-1B. It is sized for a 65mm rod x 140mm bore cylinder. Kit contents: Wiper, U cup, 3pc oring, 4pc rod seal, T seal, wear band and backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e135-63-05020\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D57S-1B\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e65mm rod x 140mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, 3pc oring, 4pc rod seal, T seal, wear band and backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 135-63-05020 on Komatsu D57S-1B. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 135-63-05020.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"3-Pack","offer_id":48855047274701,"sku":"SK.135-63-05020-KOM.3.BI.OEM","price":326.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_3e7c66dc-5b01-45c9-b337-c5950f0a0073.jpg?v=1794371140"},{"product_id":"135-63-05060-lift-cylinder-seal-kit-fits-komatsu-d57s-1b-70mm-rod-x-150mm-bore","title":"135-63-05060 Lift Cylinder Seal Kit Fits Komatsu D57S-1B, 70mm rod x 150mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 135-63-05060, for the lift cylinder on Komatsu D57S-1B. It is sized for a 70mm rod x 150mm bore cylinder. Kit contents: Wiper, U cup, 3pc oring, 4pc rod seal, T seal, wear band and backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e135-63-05060\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D57S-1B\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eLift Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e70mm rod x 150mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, 3pc oring, 4pc rod seal, T seal, wear band and backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 135-63-05060 on Komatsu D57S-1B. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 135-63-05060.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"3-Pack","offer_id":48855047307469,"sku":"SK.135-63-05060-KOM.3.BI.OEM","price":387.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_fe33065d-29e6-4eee-8628-7b1a49a5673c.jpg?v=1794371142"},{"product_id":"141-63-05010-hydraulic-cylinder-seal-kit-fits-komatsu-d60","title":"141-63-05010 Hydraulic Cylinder Seal Kit Fits Komatsu D60 - D65S-8, 60mm rod x 140mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 141-63-05010 on Komatsu D60 - D65S-8. It is sized for a 60mm rod x 140mm bore cylinder. Kit contents: Wiper, U cup, 5pc oring, 4pc rod seal, T seal, wear band and backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e141-63-05010\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D60 - D65S-8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e60mm rod x 140mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, 5pc oring, 4pc rod seal, T seal, wear band and backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 141-63-05010 on Komatsu D60 - D65S-8. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 141-63-05010.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"3-Pack","offer_id":48855047373005,"sku":"SK.141-63-05010-KOM.3.BI.OEM","price":392.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_4dc85ac9-e2a0-4f69-b608-2f524ab194df.jpg?v=1794371143"},{"product_id":"144-60-00050k-lift-cylinder-seal-kit-fits-komatsu-d65a-6-65mm-rod-x-110mm-bore","title":"144-60-00050K Lift Cylinder Seal Kit Fits Komatsu D65A-6, 65mm rod x 110mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 144-60-00050K, for the lift cylinder on Komatsu D65A-6. It is sized for a 65mm rod x 110mm bore cylinder. Kit contents: Wiper, U cup, 8pc oring, 2pc buffer seal, 2pc rod seal, 2pc wear band and backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e144-60-00050K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D65A-6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eLift Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e65mm rod x 110mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, 8pc oring, 2pc buffer seal, 2pc rod seal, 2pc wear band and backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 144-60-00050K on Komatsu D65A-6. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 144-60-00050K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"3-Pack","offer_id":48855047405773,"sku":"SK.144-60-00050K-KOM.3.BI.OEM","price":479.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_98849818-3f44-4d1b-b491-a6f2bbcd01d3.jpg?v=1794371146"},{"product_id":"144-63-05020-lift-cylinder-seal-kit-fits-komatsu-d60","title":"144-63-05020 Lift Cylinder Seal Kit Fits Komatsu D60 - D65P-7, 65mm rod x 110mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 144-63-05020, for the lift cylinder on Komatsu D60 - D65P-7. It is sized for a 65mm rod x 110mm bore cylinder. Kit contents: Wiper, U cup, 6pc oring, 2pc rod seal, T seal, wear band and 2pc backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e144-63-05020\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D60 - D65P-7\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eLift Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e65mm rod x 110mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, 6pc oring, 2pc rod seal, T seal, wear band and 2pc backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 144-63-05020 on Komatsu D60 - D65P-7. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 144-63-05020.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"3-Pack","offer_id":48855047438541,"sku":"SK.144-63-05020-KOM.3.BI.OEM","price":261.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_0f8fd5b0-ebfe-45da-8196-3ed27d5a8006.jpg?v=1794371147"},{"product_id":"144-63-05050-lift-cylinder-seal-kit-fits-komatsu-d60a-p-d65a-p-65mm-rod-x-110mm-bore","title":"144-63-05050 Lift Cylinder Seal Kit Fits Komatsu D60A \u0026 P D65A \u0026 P, 65mm rod x 110mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 144-63-05050, for the lift cylinder on Komatsu D60A \u0026amp; P D65A \u0026amp; P. It is sized for a 65mm rod x 110mm bore cylinder. Kit contents: Wiper, U cup, 6pc oring, 2pc rod seal, T seal, wear band and 2pc backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e144-63-05050\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D60A \u0026amp; P D65A \u0026amp; P\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eLift Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e65mm rod x 110mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, 6pc oring, 2pc rod seal, T seal, wear band and 2pc backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 144-63-05050 on Komatsu D60A \u0026amp; P D65A \u0026amp; P. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 144-63-05050.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"3-Pack","offer_id":48855047471309,"sku":"SK.144-63-05050-KOM.3.BI.OEM","price":251.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_1c384bd7-8c36-49bc-9331-a064ff77e36d.jpg?v=1794371148"},{"product_id":"144-63-05080-tilt-cylinder-seal-kit-fits-komatsu-d60","title":"144-63-05080 Tilt Cylinder Seal Kit Fits Komatsu D60 - D83P-1, 70mm rod x 160mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 144-63-05080, for the tilt cylinder on Komatsu D60 - D83P-1. It is sized for a 70mm rod x 160mm bore cylinder. Kit contents: Wiper, U cup, 2pc oring, 2pc rod seal, T seal, wear band and backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e144-63-05080\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D60 - D83P-1\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eTilt Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e70mm rod x 160mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, 2pc oring, 2pc rod seal, T seal, wear band and backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 144-63-05080 on Komatsu D60 - D83P-1. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 144-63-05080.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"3-Pack","offer_id":48855047504077,"sku":"SK.144-63-05080-KOM.3.BI.OEM","price":383.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_936ae203-11e7-4d23-bf36-1373771343cc.jpg?v=1794371148"},{"product_id":"144-63-12200k-lift-cylinder-seal-kit-fits-komatsu-d65p-6-65mm-rod-x-110mm-bore","title":"144-63-12200K Lift Cylinder Seal Kit Fits Komatsu D65P-6, 65mm rod x 110mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 144-63-12200K, for the lift cylinder on Komatsu D65P-6. It is sized for a 65mm rod x 110mm bore cylinder. Kit contents: Wiper, U cup, 2pc oring, T seal, wear band and backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e144-63-12200K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D65P-6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eLift Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e65mm rod x 110mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, 2pc oring, T seal, wear band and backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 144-63-12200K on Komatsu D65P-6. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 144-63-12200K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855047536845,"sku":"SK.144-63-12200K-KOM.BI.OEM","price":228.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_31e6d8a7-d544-484c-a053-78845c239dee.jpg?v=1794371151"},{"product_id":"144-63-52100k-tilt-cylinder-seal-kit-fits-komatsu-d65p-6-70mm-rod-x-160mm-bore","title":"144-63-52100K Tilt Cylinder Seal Kit Fits Komatsu D65P-6, 70mm rod x 160mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 144-63-52100K, for the tilt cylinder on Komatsu D65P-6. It is sized for a 70mm rod x 160mm bore cylinder. Kit contents: Wiper, U cup, 5pc oring, T seal, wear band and backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e144-63-52100K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D65P-6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eTilt Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e70mm rod x 160mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, 5pc oring, T seal, wear band and backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 144-63-52100K on Komatsu D65P-6. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 144-63-52100K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"3-Pack","offer_id":48855047569613,"sku":"SK.144-63-52100K-KOM.3.BI.OEM","price":809.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_e9173b4c-1464-41aa-948c-baea3808d8e8.jpg?v=1794371153"},{"product_id":"175-63-05140-tilt-cylinder-seal-kit-fits-komatsu-d155a-d155a-2-90mm-rod-x-225mm-bore","title":"175-63-05140 Tilt Cylinder Seal Kit Fits Komatsu D155A-D155A-2, 90mm rod x 225mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 175-63-05140, for the tilt cylinder on Komatsu D155A-D155A-2. It is sized for a 90mm rod x 225mm bore cylinder. Kit contents: Wiper, U cup, 4pc oring, T s eal, wear band and backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e175-63-05140\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D155A-D155A-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eTilt Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e90mm rod x 225mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, 4pc oring, T s eal, wear band and backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 175-63-05140 on Komatsu D155A-D155A-2. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 175-63-05140.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855052714189,"sku":"SK.175-63-05140-KOM.BI.OEM","price":152.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_8b2dae88-540d-4744-8f15-15400f5b3703.jpg?v=1794371325"},{"product_id":"195-63-05120-lift-cylinder-seal-kit-fits-komatsu-d355a-3-90mm-rod-x-160mm-bore","title":"195-63-05120 Lift Cylinder Seal Kit Fits Komatsu D355A-3, 90mm rod x 160mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 195-63-05120, for the lift cylinder on Komatsu D355A-3. It is sized for a 90mm rod x 160mm bore cylinder. Kit contents: Wiper, U cup, 4pc oring, T s eal, wear band and backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e195-63-05120\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D355A-3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eLift Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e90mm rod x 160mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, 4pc oring, T s eal, wear band and backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 195-63-05120 on Komatsu D355A-3. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 195-63-05120.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855058448589,"sku":"SK.195-63-05120-KOM.BI.OEM","price":286.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_56d6cdce-78fd-4e72-ba09-3389b5438174.jpg?v=1794371557"},{"product_id":"195-63-05130-tilt-cylinder-seal-kit-fits-komatsu-d355a-3-90mm-rod-x-160mm-bore","title":"195-63-05130 Tilt Cylinder Seal Kit Fits Komatsu D355A-3, 90mm rod x 160mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 195-63-05130, for the tilt cylinder on Komatsu D355A-3. It is sized for a 90mm rod x 160mm bore cylinder. Kit contents: Wiper, U cup, 4pc oring, T s eal, wear band and backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e195-63-05130\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D355A-3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eTilt Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e90mm rod x 160mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, 4pc oring, T s eal, wear band and backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 195-63-05130 on Komatsu D355A-3. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 195-63-05130.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855058481357,"sku":"SK.195-63-05130-KOM.BI.OEM","price":274.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_ce344495-9c55-4dcc-b946-6add4bf9c1bb.jpg?v=1794371558"},{"product_id":"205-63-94100k-hydraulic-cylinder-seal-kit-fits-komatsu-pc220lc-8-80mm-rod-x-130mm-bore","title":"205-63-94100K Hydraulic Cylinder Seal Kit Fits Komatsu PC220LC-8, 80mm rod x 130mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 205-63-94100K on Komatsu PC220LC-8. It is sized for a 80mm rod x 130mm bore cylinder. Kit contents: Wiper, U cup, T seal, wear band, oring and backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e205-63-94100K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC220LC-8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e80mm rod x 130mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, T seal, wear band, oring and backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 205-63-94100K on Komatsu PC220LC-8. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 205-63-94100K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"3-Pack","offer_id":48855058677965,"sku":"SK.205-63-94100K-KOM.3.BI.OEM","price":220.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_76c44602-40f2-42d2-85e8-935c6651ed92.jpg?v=1794371567"},{"product_id":"206-63-k1240k-boom-lh-cylinder-seal-kit-fits-komatsu-pc240-6k-95mm-rod-x-135mm-bore","title":"206-63-K1240K Boom LH Cylinder Seal Kit Fits Komatsu PC240-6K, 95mm rod x 135mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 206-63-K1240K, for the boom lh cylinder on Komatsu PC240-6K. It is sized for a 95mm rod x 135mm bore cylinder. Kit contents: Wiper, 2pc U cup, 4pc rod seal, T seal, 2pc wear band, 2pc oring and 5pc backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e206-63-K1240K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC240-6K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eBoom LH Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e95mm rod x 135mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, 2pc U cup, 4pc rod seal, T seal, 2pc wear band, 2pc oring and 5pc backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 206-63-K1240K on Komatsu PC240-6K. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 206-63-K1240K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"3-Pack","offer_id":48855058710733,"sku":"SK.206-63-K1240K-KOM.3.BI.OEM","price":468.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_7a9315a0-cd82-4d20-a10a-c94f1965dc2b.jpg?v=1794371568"},{"product_id":"206-63-k1250k-boom-cylinder-seal-kit-fits-komatsu-pc240-6k-95mm-rod-x-135mm-bore","title":"206-63-K1250K Boom Cylinder Seal Kit Fits Komatsu PC240-6K, 95mm rod x 135mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 206-63-K1250K, for the boom cylinder on Komatsu PC240-6K. It is sized for a 95mm rod x 135mm bore cylinder. Kit contents: Wiper, 2pc U cup, 4pc rod seal, T seal, 2pc wear band, 2pc oring and 4pc backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e206-63-K1250K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC240-6K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eBoom Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e95mm rod x 135mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, 2pc U cup, 4pc rod seal, T seal, 2pc wear band, 2pc oring and 4pc backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 206-63-K1250K on Komatsu PC240-6K. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 206-63-K1250K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"3-Pack","offer_id":48855058743501,"sku":"SK.206-63-K1250K-KOM.3.BI.OEM","price":468.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_9bc36373-e772-4f82-b213-7c825aab6416.jpg?v=1794371569"},{"product_id":"206-63-k1610k-arm-cylinder-seal-kit-fits-komatsu-pc290lc-6k-110mm-rod-x-150mm-bore","title":"206-63-K1610K Arm Cylinder Seal Kit Fits Komatsu PC290LC-6K, 110mm rod x 150mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 206-63-K1610K, for the arm cylinder on Komatsu PC290LC-6K. It is sized for a 110mm rod x 150mm bore cylinder. Kit contents: Wiper, 2pc U cup, 4pc rod seal, T seal, 2pc wear band, 4pc oring and 6pc backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e206-63-K1610K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC290LC-6K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eArm Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e110mm rod x 150mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, 2pc U cup, 4pc rod seal, T seal, 2pc wear band, 4pc oring and 6pc backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 206-63-K1610K on Komatsu PC290LC-6K. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 206-63-K1610K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"3-Pack","offer_id":48855058776269,"sku":"SK.206-63-K1610K-KOM.3.BI.OEM","price":527.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_b7a37b12-5223-42d5-9f24-78d72c2fd118.jpg?v=1794371570"},{"product_id":"206-63-k2120k-boom-cylinder-seal-kit-fits-komatsu-pc240-6k-95mm-rod-x-135mm-bore","title":"206-63-K2120K Boom Cylinder Seal Kit Fits Komatsu PC240-6K, 95mm rod x 135mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 206-63-K2120K, for the boom cylinder on Komatsu PC240-6K. It is sized for a 95mm rod x 135mm bore cylinder. Kit contents: Wiper, 2pc U cup, 4pc rod seal, T seal, 2pc wear band, 3pc oring, and 4pc backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e206-63-K2120K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC240-6K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eBoom Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e95mm rod x 135mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, 2pc U cup, 4pc rod seal, T seal, 2pc wear band, 3pc oring, and 4pc backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 206-63-K2120K on Komatsu PC240-6K. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 206-63-K2120K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"3-Pack","offer_id":48855058809037,"sku":"SK.206-63-K2120K-KOM.3.BI.OEM","price":465.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_b12c6e79-fcd1-49d4-82a2-f418ebc9c4b9.jpg?v=1794371572"},{"product_id":"206-63-k2150k-boom-cylinder-seal-kit-fits-komatsu-pc240-6k-120mm-rod-x-185mm-bore","title":"206-63-K2150K Boom Cylinder Seal Kit Fits Komatsu PC240-6K, 120mm rod x 185mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 206-63-K2150K, for the boom cylinder on Komatsu PC240-6K. It is sized for a 120mm rod x 185mm bore cylinder. Kit contents: Wiper, 2pc U cup, 4pc rod seal,T seal, 2pc wear band and 4pc backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e206-63-K2150K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC240-6K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eBoom Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e120mm rod x 185mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, 2pc U cup, 4pc rod seal,T seal, 2pc wear band and 4pc backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 206-63-K2150K on Komatsu PC240-6K. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 206-63-K2150K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"3-Pack","offer_id":48855058841805,"sku":"SK.206-63-K2150K-KOM.3.BI.OEM","price":761.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_fd2003da-572d-4ac2-a1b9-d21339025962.jpg?v=1794371573"},{"product_id":"207-63-k1230k-boom-cylinder-seal-kit-fits-komatsu-pc340-6k-100mm-rod-x-140mm-bore","title":"207-63-K1230K Boom Cylinder Seal Kit Fits Komatsu PC340-6K, 100mm rod x 140mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 207-63-K1230K, for the boom cylinder on Komatsu PC340-6K. It is sized for a 100mm rod x 140mm bore cylinder. Kit contents: Wiper, 2pc U cup, 4pc rod seal,T seal, 2pc wear band, 3pc oring and 4pc backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e207-63-K1230K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC340-6K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eBoom Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e100mm rod x 140mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, 2pc U cup, 4pc rod seal,T seal, 2pc wear band, 3pc oring and 4pc backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 207-63-K1230K on Komatsu PC340-6K. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 207-63-K1230K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"3-Pack","offer_id":48855058907341,"sku":"SK.207-63-K1230K-KOM.3.BI.OEM","price":497.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_abf505af-5e16-4f34-967f-1f7e423e9a9a.jpg?v=1794371575"},{"product_id":"20e-63-03240k-boom-lift-cylinder-seal-kit-fits-komatsu-pc130-7k-70mm-rod-x-105mm-bore","title":"20E-63-03240K Boom Lift Cylinder Seal Kit Fits Komatsu PC130-7K, 70mm rod x 105mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 20E-63-03240K, for the boom lift cylinder on Komatsu PC130-7K. It is sized for a 70mm rod x 105mm bore cylinder. Kit contents: Wiper, 2pc U cup, 2pc oring, 4pc rod seal, T s eal, 2pc wear band and 3pc backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e20E-63-03240K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC130-7K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eBoom Lift Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e70mm rod x 105mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, 2pc U cup, 2pc oring, 4pc rod seal, T s eal, 2pc wear band and 3pc backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 20E-63-03240K on Komatsu PC130-7K. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 20E-63-03240K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855058972877,"sku":"SK.20E-63-03240K-KOM.BI.OEM","price":172.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_5d2278e2-8eb5-44f0-bec1-dda333fcbf3b.jpg?v=1794371578"},{"product_id":"20e-63-k2500k-boom-adj-cylinder-seal-kit-fits-komatsu-pc130-7k-70mm-rod-x-140mm-bore","title":"20E-63-K2500K Boom Adj Cylinder Seal Kit Fits Komatsu PC130-7K, 70mm rod x 140mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 20E-63-K2500K, for the boom adj cylinder on Komatsu PC130-7K. It is sized for a 70mm rod x 140mm bore cylinder. Kit contents: Wiper, 2pc U cup, oring, 4pc rod seal, T s eal, 2pc wear band and backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e20E-63-K2500K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC130-7K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eBoom Adj Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e70mm rod x 140mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, 2pc U cup, oring, 4pc rod seal, T s eal, 2pc wear band and backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 20E-63-K2500K on Komatsu PC130-7K. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 20E-63-K2500K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855059005645,"sku":"SK.20E-63-K2500K-KOM.BI.OEM","price":141.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_03eab3b2-cccf-48ca-a1e6-b44ce5305604.jpg?v=1794371579"},{"product_id":"20g-63-k1110k-boom-cylinder-seal-kit-fits-komatsu-pc150-6k-100mm-rod-x-160mm-bore","title":"20G-63-K1110K Boom Cylinder Seal Kit Fits Komatsu PC150-6K, 100mm rod x 160mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 20G-63-K1110K, for the boom cylinder on Komatsu PC150-6K. It is sized for a 100mm rod x 160mm bore cylinder. Kit contents: 4pc Wiper, 2pc U cup, 8pc oring, T s eal, 2pc wear band and 3pc backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e20G-63-K1110K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC150-6K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eBoom Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e100mm rod x 160mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e4pc Wiper, 2pc U cup, 8pc oring, T s eal, 2pc wear band and 3pc backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 20G-63-K1110K on Komatsu PC150-6K. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 20G-63-K1110K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855059038413,"sku":"SK.20G-63-K1110K-KOM.BI.OEM","price":337.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_2d393a21-a5ad-49f6-86d6-fb87bf74e166.jpg?v=1794371582"},{"product_id":"20u-63-02050k-blade-cylinder-seal-kit-fits-komatsu-pc50uu-1-60mm-rod-x-100mm-bore","title":"20U-63-02050K Blade Cylinder Seal Kit Fits Komatsu PC50UU-1, 60mm rod x 100mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 20U-63-02050K, for the blade cylinder on Komatsu PC50UU-1. It is sized for a 60mm rod x 100mm bore cylinder. Kit contents: Wiper, U cup, 3pc oring, T s eal, wear band and backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e20U-63-02050K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC50UU-1\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eBlade Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e60mm rod x 100mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, 3pc oring, T s eal, wear band and backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 20U-63-02050K on Komatsu PC50UU-1. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 20U-63-02050K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855059071181,"sku":"SK.20U-63-02050K-KOM.BI.OEM","price":74.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_1228a5ed-2019-4fe1-aa5b-ab8dfe95679f.jpg?v=1794371584"},{"product_id":"20u-63-02051k-blade-cylinder-seal-kit-fits-komatsu-pc50uu-1-60mm-rod-x-100mm-bore","title":"20U-63-02051K Blade Cylinder Seal Kit Fits Komatsu PC50UU-1, 60mm rod x 100mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 20U-63-02051K, for the blade cylinder on Komatsu PC50UU-1. It is sized for a 60mm rod x 100mm bore cylinder. Kit contents: Wiper, U cup, 3pc oring, T s eal, wear band and backup seals New.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e20U-63-02051K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC50UU-1\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eBlade Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e60mm rod x 100mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, 3pc oring, T s eal, wear band and backup seals New\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 20U-63-02051K on Komatsu PC50UU-1. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 20U-63-02051K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855059103949,"sku":"SK.20U-63-02051K-KOM.BI.OEM","price":74.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_fe1b734c-7916-4cf7-9cae-f12d2bd7ca6e.jpg?v=1794371584"},{"product_id":"21d-61-13160-bucket-cylinder-seal-kit-fits-komatsu-pc95r-2-60mm-rod-x-90mm-bore","title":"21D-61-13160 Bucket Cylinder Seal Kit Fits Komatsu PC95R-2, 60mm rod x 90mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 21D-61-13160, for the bucket cylinder on Komatsu PC95R-2. It is sized for a 60mm rod x 90mm bore cylinder. Kit contents: Wiper, U cup, Buffer, 4pc rod seal, 5pc wear band, T seal , 2pc oring and 3pc backup seals.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e21D-61-13160\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC95R-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eBucket Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e60mm rod x 90mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, Buffer, 4pc rod seal, 5pc wear band, T seal , 2pc oring and 3pc backup seals\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 21D-61-13160 on Komatsu PC95R-2. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 21D-61-13160.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855059562701,"sku":"SK.21D-61-13160-KOM.BI.OEM","price":125.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_5093b17e-e309-4b89-8953-7c2f63e52393.jpg?v=1794371603"},{"product_id":"21d-61-14140-boom-swing-cylinder-seal-kit-fits-komatsu-pc95r-2-60mm-rod-x-100mm-bore","title":"21D-61-14140 Boom Swing Cylinder Seal Kit Fits Komatsu PC95R-2, 60mm rod x 100mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 21D-61-14140, for the boom swing cylinder on Komatsu PC95R-2. It is sized for a 60mm rod x 100mm bore cylinder. Kit contents: Wiper, U cup, Buffer, 4pc rod seal, 5pc wear band, T seal , 2pc oring and 3pc backup seals.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e21D-61-14140\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC95R-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eBoom Swing Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e60mm rod x 100mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, Buffer, 4pc rod seal, 5pc wear band, T seal , 2pc oring and 3pc backup seals\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 21D-61-14140 on Komatsu PC95R-2. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 21D-61-14140.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855059595469,"sku":"SK.21D-61-14140-KOM.BI.OEM","price":134.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_ad9ea644-43a2-4df7-846b-2a8c239e953e.jpg?v=1794371605"},{"product_id":"21p-63-03120k-arm-cylinder-seal-kit-fits-komatsu-pc150-6k-pc150lc-6k-85mm-rod-x-120mm-bore","title":"21P-63-03120K Arm Cylinder Seal Kit Fits Komatsu PC150-6K PC150LC-6K+, 85mm rod x 120mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 21P-63-03120K, for the arm cylinder on Komatsu PC150-6K PC150LC-6K+. It is sized for a 85mm rod x 120mm bore cylinder. Kit contents: Wiper, 2pc U cup, 4pc rod seal, 2pc wear band, T seal , 4pc oring and 5pc backup seals.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e21P-63-03120K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC150-6K PC150LC-6K+\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eArm Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e85mm rod x 120mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, 2pc U cup, 4pc rod seal, 2pc wear band, T seal , 4pc oring and 5pc backup seals\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 21P-63-03120K on Komatsu PC150-6K PC150LC-6K+. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 21P-63-03120K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855059628237,"sku":"SK.21P-63-03120K-KOM.BI.OEM","price":154.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_0195b405-683f-442b-a963-4340f03e694e.jpg?v=1794371606"},{"product_id":"21p-63-03130k-bucket-cylinder-seal-kit-fits-komatsu-pc150-6k-pc150lc-6k-70mm-rod-x-105mm-b","title":"21P-63-03130K Bucket Cylinder Seal Kit Fits Komatsu PC150-6K PC150LC-6K+, 70mm rod x 105mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 21P-63-03130K, for the bucket cylinder on Komatsu PC150-6K PC150LC-6K+. It is sized for a 70mm rod x 105mm bore cylinder. Kit contents: Wiper, 2pc U cup, 4pc rod seal, 2pc wear band, T seal , 4pc oring and 3pc backup seals.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e21P-63-03130K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC150-6K PC150LC-6K+\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eBucket Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e70mm rod x 105mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, 2pc U cup, 4pc rod seal, 2pc wear band, T seal , 4pc oring and 3pc backup seals\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 21P-63-03130K on Komatsu PC150-6K PC150LC-6K+. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 21P-63-03130K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855059661005,"sku":"SK.21P-63-03130K-KOM.BI.OEM","price":136.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_11b1b073-fc3f-49bf-99f7-ab0cc2fbcee8.jpg?v=1794371606"},{"product_id":"21p-63-03200k-boom-cylinder-seal-kit-fits-komatsu-pc150-6k-pc150lc-6k-75mm-rod-x-110mm-bor","title":"21P-63-03200K Boom Cylinder Seal Kit Fits Komatsu PC150-6K PC150LC-6K+, 75mm rod x 110mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 21P-63-03200K, for the boom cylinder on Komatsu PC150-6K PC150LC-6K+. It is sized for a 75mm rod x 110mm bore cylinder. Kit contents: Wiper, 2pc U cup, 4pc rod seal, 2pc wear band, T seal , 3pc oring and 3pc backup seals.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e21P-63-03200K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC150-6K PC150LC-6K+\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eBoom Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e75mm rod x 110mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, 2pc U cup, 4pc rod seal, 2pc wear band, T seal , 3pc oring and 3pc backup seals\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 21P-63-03200K on Komatsu PC150-6K PC150LC-6K+. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 21P-63-03200K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855059693773,"sku":"SK.21P-63-03200K-KOM.BI.OEM","price":111.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_ac0bb7b5-123c-41a0-bf5d-a4a986c2959c.jpg?v=1794371608"},{"product_id":"21p-63-k1611k-boom-cylinder-seal-kit-fits-komatsu-pc150-6k-pc150lc-6k-75mm-rod-x-110mm-bor","title":"21P-63-K1611K Boom Cylinder Seal Kit Fits Komatsu PC150-6K PC150LC-6K+, 75mm rod x 110mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 21P-63-K1611K, for the boom cylinder on Komatsu PC150-6K PC150LC-6K+. It is sized for a 75mm rod x 110mm bore cylinder. Kit contents: Wiper, 2pc U cup, 4pc rod seal, 2pc wear band, T seal , 3pc oring and backup seals.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e21P-63-K1611K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC150-6K PC150LC-6K+\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eBoom Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e75mm rod x 110mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, 2pc U cup, 4pc rod seal, 2pc wear band, T seal , 3pc oring and backup seals\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 21P-63-K1611K on Komatsu PC150-6K PC150LC-6K+. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 21P-63-K1611K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855059726541,"sku":"SK.21P-63-K1611K-KOM.BI.OEM","price":120.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_e7f90f57-dba4-44d6-9397-37f7ea8bc06b.jpg?v=1794371610"},{"product_id":"21p-63-k1711k-arm-cylinder-seal-kit-fits-komatsu-pc150-6k-pc150lc-6k-85mm-rod-x-120mm-bore","title":"21P-63-K1711K Arm Cylinder Seal Kit Fits Komatsu PC150-6K PC150LC-6K+, 85mm rod x 120mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 21P-63-K1711K, for the arm cylinder on Komatsu PC150-6K PC150LC-6K+. It is sized for a 85mm rod x 120mm bore cylinder. Kit contents: Wiper, 2pc U cup, 2pc wear band, T seal , 3pc oring and 4pc backup seals.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e21P-63-K1711K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC150-6K PC150LC-6K+\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eArm Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e85mm rod x 120mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, 2pc U cup, 2pc wear band, T seal , 3pc oring and 4pc backup seals\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 21P-63-K1711K on Komatsu PC150-6K PC150LC-6K+. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 21P-63-K1711K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855059759309,"sku":"SK.21P-63-K1711K-KOM.BI.OEM","price":141.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_4e4559dd-36b0-4896-97f1-0d913b634728.jpg?v=1794371611"},{"product_id":"21p-63-k1821k-bucket-cylinder-seal-kit-fits-komatsu-pc150-6k-pc150lc-6k-75mm-rod-x-110mm-b","title":"21P-63-K1821K Bucket Cylinder Seal Kit Fits Komatsu PC150-6K PC150LC-6K, 75mm rod x 110mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 21P-63-K1821K, for the bucket cylinder on Komatsu PC150-6K PC150LC-6K. It is sized for a 75mm rod x 110mm bore cylinder. Kit contents: 3pc Wiper, 2pc U cup, 2pc wear band, T seal , 3pc oring, 2pc rod seal and 4pc backup seals.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e21P-63-K1821K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC150-6K PC150LC-6K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eBucket Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e75mm rod x 110mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e3pc Wiper, 2pc U cup, 2pc wear band, T seal , 3pc oring, 2pc rod seal and 4pc backup seals\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 21P-63-K1821K on Komatsu PC150-6K PC150LC-6K. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 21P-63-K1821K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855059792077,"sku":"SK.21P-63-K1821K-KOM.BI.OEM","price":122.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_57a71c4a-34c7-4b12-949b-944a5f575bb0.jpg?v=1794371612"},{"product_id":"21p-63-k3600k-bucket-cylinder-seal-kit-fits-komatsu-pc150-6k-pc150lc-6k-70mm-rod-x-105mm-b","title":"21P-63-K3600K Bucket Cylinder Seal Kit Fits Komatsu PC150-6K PC150LC-6K+, 70mm rod x 105mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 21P-63-K3600K, for the bucket cylinder on Komatsu PC150-6K PC150LC-6K+. It is sized for a 70mm rod x 105mm bore cylinder. Kit contents: 3pc Wiper, 2pc U cup, 2pc wear band, T seal , 3pc oring, 2pc rod seal and 4pc backup seals.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e21P-63-K3600K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC150-6K PC150LC-6K+\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eBucket Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e70mm rod x 105mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e3pc Wiper, 2pc U cup, 2pc wear band, T seal , 3pc oring, 2pc rod seal and 4pc backup seals\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 21P-63-K3600K on Komatsu PC150-6K PC150LC-6K+. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 21P-63-K3600K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855059824845,"sku":"SK.21P-63-K3600K-KOM.BI.OEM","price":169.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_d2ae28c1-956b-4b9c-a08c-44e7df2d37d8.jpg?v=1794371614"},{"product_id":"21s-63-02050k-hydraulic-cylinder-seal-kit-fits-komatsu-d20a-7-d21a-7-25mm-rod-x-50mm-bore","title":"21S-63-02050K Hydraulic Cylinder Seal Kit Fits Komatsu D20A-7 D21A-7, 25mm rod x 50mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 21S-63-02050K on Komatsu D20A-7 D21A-7. It is sized for a 25mm rod x 50mm bore cylinder. Kit contents: Wiper, U cup, 4pc rod seal, wear band, Buffer , 2pc oring and backup seals.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e21S-63-02050K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu D20A-7 D21A-7\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e25mm rod x 50mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, 4pc rod seal, wear band, Buffer , 2pc oring and backup seals\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 21S-63-02050K on Komatsu D20A-7 D21A-7. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 21S-63-02050K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855059857613,"sku":"SK.21S-63-02050K-KOM.BI.OEM","price":93.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_df58d15e-870b-4daf-ba92-db2c49b5da72.jpg?v=1794371615"},{"product_id":"21s-63-02131k-bucket-cylinder-seal-kit-fits-komatsu-pc28uu-2-25mm-rod-x-50mm-bore","title":"21S-63-02131K Bucket Cylinder Seal Kit Fits Komatsu PC28UU-2, 25mm rod x 50mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 21S-63-02131K, for the bucket cylinder on Komatsu PC28UU-2. It is sized for a 25mm rod x 50mm bore cylinder. Kit contents: 5 pc Wiper, U cup, Buffer, Wear Band, 2pc oring and backup seals.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e21S-63-02131K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC28UU-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eBucket Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e25mm rod x 50mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e5 pc Wiper, U cup, Buffer, Wear Band, 2pc oring and backup seals\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 21S-63-02131K on Komatsu PC28UU-2. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 21S-63-02131K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855059890381,"sku":"SK.21S-63-02131K-KOM.BI.OEM","price":115.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_3fd300fb-ff73-448d-b595-7d8cb419d1d5.jpg?v=1794371617"},{"product_id":"21w-63-02220k-arm-cylinder-seal-kit-fits-komatsu-pc75uu-2-60mm-rod-x-100mm-bore","title":"21W-63-02220K Arm Cylinder Seal Kit Fits Komatsu PC75UU-2, 60mm rod x 100mm bore - Aftermarket Replacement","description":"\u003cp\u003eIs a hydraulic cylinder on your Komatsu leaking at the rod, drifting under load, or losing power? Worn seals are almost always the cause, and resealing the cylinder brings it back to full holding force for a fraction of the cost of a new or rebuilt cylinder.\u003c\/p\u003e\u003cp\u003eThis Beaver Island Parts Company kit is an aftermarket replacement for Komatsu seal kit 21W-63-02220K, for the arm cylinder on Komatsu PC75UU-2. It is sized for a 60mm rod x 100mm bore cylinder. Kit contents: Wiper, U cup, 4pc rod seal, T seal, wear Band, 3pc oring and backup seals.\u003c\/p\u003e\u003ch3\u003eKit Details\u003c\/h3\u003e\u003ctable class=\"bi-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eOEM reference\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e21W-63-02220K\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eFits\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eKomatsu PC75UU-2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eCylinder\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eArm Cylinder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eRod x bore\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003e60mm rod x 100mm bore\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cb\u003eIncludes\u003c\/b\u003e\u003c\/td\u003e\n\u003ctd\u003eWiper, U cup, 4pc rod seal, T seal, wear Band, 3pc oring and backup seals\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat It Fits\u003c\/h3\u003e\u003cp\u003eReplaces Komatsu part number 21W-63-02220K on Komatsu PC75UU-2. Always confirm the kit number against your machine's parts book or the stamping on the cylinder, and measure the rod and bore if the cylinder has been rebuilt before.\u003c\/p\u003e\u003ch3\u003eYou Can Do This Repair\u003c\/h3\u003e\u003cp\u003eA cylinder reseal is well within reach of a careful owner with a shop. Lower or block every implement and relieve pressure, then remove the cylinder or support it securely. Unthread the gland, pull the rod and piston, and lay out the old seals in order as a reference. Clean every groove, inspect the rod and bore for scoring, then install the new seals with a blunt seal pick (never a screwdriver). Warming polyurethane seals in hot water makes them easier to seat. Lubricate everything with clean hydraulic oil and torque the piston nut and gland to spec.\u003c\/p\u003e\u003cp\u003e\u003cb\u003ePro Tip:\u003c\/b\u003e Photograph the seal stack before you remove it, and keep the old seals until the cylinder is back in service. Matching profiles side by side removes all the guesswork.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eShipping:\u003c\/b\u003e This part is special-ordered and packed for you. It ships from our facility in about 10 business days, then transits by the carrier service you choose at checkout. The estimated delivery date shown on this page includes that lead time.\u003c\/p\u003e\u003ch3\u003eWhy Buy From Beaver Island Parts Company\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eClear fitment information.\u003c\/b\u003e OEM reference numbers and every detail we have are listed up front so you can confirm fit before you buy.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eInspected, packed and labeled by us.\u003c\/b\u003e Each order is checked and repacked in a bag labeled with the part's size and material, so it never gets lost in a parts bin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReal people who answer fitment questions.\u003c\/b\u003e We are an American family-owned and operated small business. Send us your measurements or model number and we will help you confirm the right part.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eReplacement guarantee.\u003c\/b\u003e If we ship the wrong item, or it arrives damaged or defective, we replace it free of charge.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cb\u003eQ: Is this an OEM kit?\u003c\/b\u003e\u003cbr\u003eA: No. It is an aftermarket kit built to replace Komatsu kit 21W-63-02220K.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: Will this fit my machine?\u003c\/b\u003e\u003cbr\u003eA: Match the kit number on your parts book or cylinder. If the cylinder has been rebuilt with non-original components, measure the rod and bore and contact us before ordering.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eQ: When will it ship?\u003c\/b\u003e\u003cbr\u003eA: It ships from our facility in about 10 business days, then transits by the carrier service you choose.\u003c\/p\u003e\u003cp\u003eNote: Beaver Island Parts Company is not affiliated with Komatsu. All brand names, model numbers and part numbers referenced are used solely to confirm compatibility and are the trademarks of their respective owners.\u003c\/p\u003e","brand":"Beaver Island Parts Company","offers":[{"title":"Default Title","offer_id":48855059923149,"sku":"SK.21W-63-02220K-KOM.BI.OEM","price":83.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0611\/8110\/0237\/files\/IMG-060_0d763633-b87a-48c3-9a29-34945d7b610b.jpg?v=1794371617"}],"url":"https:\/\/beaverislandparts.com\/collections\/komatsu-hydraulic-seal-kits.oembed?page=21","provider":"Beaver Island Parts Company","version":"1.0","type":"link"}